During production inspection in China, often called DUPRO or in-process inspection, is a quality control check performed while an order is still being manufactured. It helps buyers identify defects, verify production progress, and request corrective action before the entire order is completed.
For international importers, the main advantage is timing. A problem found halfway through manufacturing may still be correctable before it affects every unit. However, an inspection does not guarantee that all finished products will meet specifications.
The most useful inspection is scheduled when enough goods have been produced to reveal meaningful quality patterns, but sufficient production remains for the factory to correct problems.
When Should You Arrange During Production Inspection in China?
During production inspection is commonly scheduled when approximately 20–50% of the order has been completed, although the appropriate point depends on the product, manufacturing process, and inspection objective. This range is a practical scheduling convention, not a universal requirement.
The inspection should take place after production has reached a representative stage.
For example, checking only a few initial units may reveal setup problems but provide limited information about consistent mass production. Waiting until almost every unit is finished leaves less time for corrective action.
| Production Stage | Inspection Opportunity | Main Limitation |
|---|---|---|
| Before mass production | Verify materials, approved samples, and production readiness | Cannot establish mass-production consistency |
| Early production | Identify setup errors and initial workmanship issues | Limited finished-unit availability |
| 20–50% completed | Check production consistency, defects, and progress | Remaining production still requires monitoring |
| Near completion | Evaluate finished goods and shipment readiness | Less opportunity for production-wide corrections |
When Is DUPRO Especially Useful?
A during production inspection is worth considering when:
-
The product involves custom specifications or complex assembly.
-
The manufacturer is producing the item for the first time.
-
Previous orders have shown recurring defects.
-
The order contains multiple SKUs, colors, or configurations.
-
A production delay could affect a fixed delivery commitment.
-
Materials or components are difficult to replace after assembly.
For simple repeat orders from a supplier with a reliable performance record, buyers may decide that routine production reporting and a final inspection are sufficient.
Inspection frequency should reflect actual risk rather than being treated as a fixed requirement for every purchase.
What Does a During Production Inspection Check?
A useful inspection covers more than the appearance of finished units. It compares the actual manufacturing process and available goods with the buyer's approved requirements.
1. Product Specifications and Approved Samples
Inspectors should confirm that production matches the agreed specifications.
Depending on the product, this may include dimensions, materials, colors, components, finishes, and labeling.
The approved sample should be available as a reference, but it should not replace detailed written specifications.
A sample may represent one acceptable unit without defining every allowable tolerance or functional requirement.
2. Workmanship and Visible Defects
Inspectors examine available products for issues such as scratches, deformation, poor assembly, inconsistent finishes, missing components, or incorrect labeling.
The relevant defect categories depend on the product.
A cosmetic defect on decorative packaging may have a different commercial impact from an assembly defect affecting an electrical component.
Buyers should define defect classifications and acceptance criteria before inspection.
3. Functional and Performance Checks
Where suitable equipment and test methods are available, inspectors may conduct agreed functional checks.
Examples include:
-
Operating buttons, switches, or mechanical parts.
-
Checking assembly fit and movement.
-
Measuring dimensions against drawings.
-
Confirming basic electrical or mechanical functions.
-
Reviewing available production test records.
A factory-floor functional check is not automatically equivalent to laboratory testing, certification, or regulatory compliance assessment.
If a product requires specialized testing, the buyer should arrange that separately.
4. Raw Materials and Components
Material substitution can affect product performance, appearance, and consistency.
Inspectors may compare available raw materials and components with approved specifications, supplier documentation, or traceability records.
For higher-risk components, documentary checks may need to be supported by additional testing.
5. Production Progress and Capacity
DUPRO can also help buyers understand whether the order is progressing according to schedule.
The inspector may record completed quantities, work-in-progress, available materials, production-line activity, and the factory's stated completion plan.
A progress check should distinguish between quantities started, assembled, finished, and accepted.
For example, 5,000 units assembled does not necessarily mean 5,000 units have passed quality control.
6. Packaging and Identification
If packaging has started, inspectors may verify carton markings, product labels, barcode information, packing quantities, and protective materials.
Packaging that has not yet been completed should be recorded as unverified rather than automatically marked as acceptable.
How Does a During Production Inspection Work?
A structured inspection normally follows an agreed scope rather than a generic factory checklist.
Step 1: Prepare the Inspection Requirements
Before booking an inspection, the buyer should provide:
-
Purchase order and product specifications.
-
Approved samples or reference photographs.
-
Drawings and measurement tolerances.
-
Required functional checks.
-
Defect classifications and acceptance criteria.
-
Order quantities and SKU breakdown.
-
Production schedule and factory contact details.
The inspector should confirm which checks are feasible at the selected production stage.
Step 2: Confirm the Production Status
The buyer or inspection provider should verify that sufficient production has been completed.
If the factory has not reached the agreed inspection stage, the visit may need to be rescheduled.
Production completion percentages should be supported by actual quantities where possible.
Step 3: Inspect Available Goods and Processes
The inspector examines the products and production activities included in the agreed scope.
Where sampling is used, the sampling method, lot definition, sample size, and acceptance criteria should be specified.
Buyers should not assume that every DUPRO inspection uses the same sampling standard.
Step 4: Review Findings and Evidence
The inspection report should identify the products checked, observed defects, relevant measurements, production status, and limitations.
Photographs are useful, but they should be linked to clear descriptions and the affected SKU or production lot.
Step 5: Agree on Corrective Actions
If the inspection identifies problems, the factory should explain the cause and propose corrective action.
The buyer should confirm whether the issue requires rework, replacement, process adjustment, additional testing, or follow-up inspection.
An inspection report identifies findings. The buyer and supplier must still agree on how those findings will be resolved.
What Should Buyers Do If DUPRO Finds Defects?
Not every defect requires stopping production. The response should depend on the severity, frequency, and likely cause of the issue.
| Finding | Possible Buyer Response | Follow-Up Evidence |
|---|---|---|
| Minor cosmetic variation | Confirm whether it falls within agreed tolerances | Updated inspection records |
| Repeated assembly defect | Request process correction and affected-unit review | Corrective action report and reinspection |
| Incorrect material or component | Investigate affected batches and approved specifications | Material records and verification results |
| Functional failure | Assess whether production should pause pending investigation | Test results and corrective action evidence |
| Production delay | Request a revised milestone schedule | Updated quantities and completion dates |
| Unavailable test or incomplete assembly | Record the limitation and schedule later verification | Additional test or inspection report |
Consider a hypothetical order of 10,000 customized products. At the midpoint, an inspector identifies an incorrect component in several sampled units.
The buyer should not automatically assume that every unit is defective. The factory should first determine which production batches used the component, identify affected quantities, and establish a corrective plan.
If the defect relates to a critical safety requirement, additional specialist assessment may be necessary before production continues.
The important distinction is between discovering a problem and confirming that the problem has been effectively corrected.
During Production Inspection vs Pre-Shipment Inspection
These inspections serve different purposes.
| Comparison Point | During Production Inspection | Pre-Shipment Inspection |
|---|---|---|
| Timing | While manufacturing is underway | When the agreed portion of the order is finished and available |
| Primary Objective | Detect problems early and assess production progress | Assess finished goods before shipment |
| Products Available | Completed units and work-in-progress | Finished units ready for inspection |
| Corrective Opportunity | Potentially more time for process changes | Often less time before shipment |
| Main Limitation | Cannot confirm the quality of all future production | May discover defects late in the process |
DUPRO should not automatically replace pre-shipment inspection.
A factory may correct problems identified during production, but later manufacturing batches can still introduce new defects.
For orders with substantial quality or delivery risk, buyers may use both inspections at different stages.
The appropriate combination depends on product complexity, supplier performance, and the cost of quality failure.
During Production Inspection Checklist for China Buyers
Before arranging an inspection, confirm the following items with the manufacturer and inspection provider.
| Checklist Item | Buyer Question |
|---|---|
| Production Stage | Has enough of the order been completed for a meaningful inspection? |
| Product Reference | Are approved specifications and samples available? |
| Inspection Scope | Which SKUs, processes, and production lots will be checked? |
| Sampling Plan | How will units be selected and evaluated? |
| Workmanship | Which defects are unacceptable? |
| Dimensions | What measurement tolerances apply? |
| Functionality | Which tests can be performed at this stage? |
| Materials | How will critical components be verified? |
| Production Progress | What quantities are completed, pending, or rejected? |
| Corrective Action | Who is responsible for fixing identified problems? |
| Follow-Up | Will reinspection or additional evidence be required? |
| Reporting | When will the buyer receive the findings? |
For a new supplier, inspection planning should also be supported by appropriate supplier due diligence. Buyers can review how to find reliable suppliers in China before committing to a production order.
If a sourcing intermediary is coordinating the inspection, clarify whether it is responsible for booking the visit, communicating findings, arranging reinspection, or managing corrective action. Buyers may also consult how to verify a China sourcing agent before payment when assessing the intermediary's identity and responsibilities.
Reference Sources
The following internal resources are relevant to the supplier verification and procurement risk topics discussed in this article:







