Other recommendations for your business
MEGAMF2000 Series is a wafer type electromagnetic flowmeter ideal for conductive liquids. It comes in sizes from 6mm to 200mm.
MEGAMF2000 Series is widely used for tap-water, waste water, food & beverage, pulp & paper and many other industrial fluid.
MEGAMF2000 Series electromagnetic flowmeter could be used in compact or remote model with 411B,511B or 211B series converter
- Light and compact version
- Quick and easy to install
- Flow Velocity range: 0.1-15m/s
- It comes any flanges such as, ANSI, DIN, JIS…etc
- Protection class: IP65 (Standard), IP67/IP68 available
- High accuracy of ±0.5% value of reading
- With forward/Reverse flowrate measurement function
- AC high-frequency switching power: 85-250VAC
- DC 24V switching power: 20-36VDC
- Modbus, HART, GPRS, PROFIBUS Communication
- Carbon steel and Stainless steel housing can be optional
- Display in instantaneous flow and accumulated flow
SPECIFICATIONS
| Sizes | 6-200mm |
| Measuring Range | 0.1-15m/s |
| Temperature |
-20~+60℃ (Neoprene) -20~+120℃ (PTFE) -40~+140℃ (FEP) -10~+60℃ (Polyurethane) -40~+180℃ (PFA) |
| Accuracy | ±0.5% |
| Liner | Polyurethane, Neoprene, FEP, PTFE, PFA |
| Flange Types | ANSI, DIN, JIS |
| Material | SS #201/304 flow tube, carbon steel flanges & coil housing, powder coated aluminum electrical enclosure |
| Conductivity | must be ≥ 5 µS/cm |
| Electrode & Grounding | Stainless Steel #316L / Hastelloy B / Hastelloy C / Titanium / Tantalum / Platinum -iridium alloy |
| Display | Flow rate, flow velocity, percentage, Total flow |
| Grounding Resistance | Must be less then 10 Ω |
| Protection | IP 65 or IP 68 (Submersible, with remote style) |
| Ambient Tempearture | -20~60 °C |
| Cable entry | M20x1.5 |
INSTALLATION
Location
Install the flowmeter in a location where it is not exposed to direct sunlight.
Noise Avoidance
The flowmeter should be installed away from electrical motors, transformers, and other power sources in order to avoid interference with measurement.
Required Lengths of Straight Runs
To maintain accurate measurement, we recommend the piping conditions as shown in the following figures.
*1: Do not install anything in the vicinity that may interfere with the magnetic field, induced signal voltages, or flow velocity distributions of the flowmeter.
*2: A straight run may not be required on the downstream side of the flowmeter. However, if a downstream valve or other fitting causes irregularity or deviation in flows, provide a straight run of 2D to 3D on the downstream side.
*3: The valves shall be mounted on the downstream side so that deviated flows do not occur in the flowtube and to avoid startup from an empty condition.
Required Lengths of Straight Runs
It is essential that pipes remain fully filled at all times, otherwise flow rate indications may be affected and measurement errors may be caused.
Piping shall be designed so as to maintain the interior of the flowtube filled with fluids. Vertical mounting is effective in such cases as when fluids tend to separate or solid matter may be precipitated. When employing vertical mounting, direct the fluids from the bottom to the top to ensure that the pipes remain fully filled.
Avoid air bubbles
If air bubbles enter a measurement pipe, flow rate indications may be affected and measurement errors may be caused.
In cases where fluids contain air bubbles, piping must be designed to prevent them from accumulating in the measurement pipe of a flow tube.
If a valve exists near the flowmeter, try to mount the flowmeter on the valve’s upstream side in order to prevent a possible reduction of pressure inside the pipe, thereby avoiding the possibility of air bubbles.
Install the flowmeter in a location where it is not exposed to direct sunlight.
Noise Avoidance
The flowmeter should be installed away from electrical motors, transformers, and other power sources in order to avoid interference with measurement.
Required Lengths of Straight Runs
To maintain accurate measurement, we recommend the piping conditions as shown in the following figures.
*2: A straight run may not be required on the downstream side of the flowmeter. However, if a downstream valve or other fitting causes irregularity or deviation in flows, provide a straight run of 2D to 3D on the downstream side.
*3: The valves shall be mounted on the downstream side so that deviated flows do not occur in the flowtube and to avoid startup from an empty condition.
Required Lengths of Straight Runs
Piping shall be designed so as to maintain the interior of the flowtube filled with fluids. Vertical mounting is effective in such cases as when fluids tend to separate or solid matter may be precipitated. When employing vertical mounting, direct the fluids from the bottom to the top to ensure that the pipes remain fully filled.
Avoid air bubbles
In cases where fluids contain air bubbles, piping must be designed to prevent them from accumulating in the measurement pipe of a flow tube.
If a valve exists near the flowmeter, try to mount the flowmeter on the valve’s upstream side in order to prevent a possible reduction of pressure inside the pipe, thereby avoiding the possibility of air bubbles.
Supplier's popular products
Contact Supplier
We have more categories for you. lf you can't find the products you want above,just fill in the form and tell us whatproducts you want to import from China.
