For home garden lighting Motion 150W Sensor Led Solar Flood Light

For home garden lighting Motion 150W Sensor Led Solar Flood Light

For home garden lighting Motion 150W Sensor Led Solar Flood Light

 1.advantages

ü  Energy saving

ü  Enviormental

ü  Safety

ü  High technology

ü  Long life

For home garden lighting Motion 150W Sensor Led Solar Flood Light

For home garden lighting Motion 150W Sensor Led Solar Flood Light

2.Application

For home garden lighting Motion 150W Sensor Led Solar Flood Light

3.Project show 

For home garden lighting Motion 150W Sensor Led Solar Flood Light

For home garden lighting Motion 150W Sensor Led Solar Flood Light

4.Product specifications 

For home garden lighting Motion 150W Sensor Led Solar Flood Light

5.Product detail  

For home garden lighting Motion 150W Sensor Led Solar Flood Light

For home garden lighting Motion 150W Sensor Led Solar Flood Light

For home garden lighting Motion 150W Sensor Led Solar Flood Light

6.Installation 

For home garden lighting Motion 150W Sensor Led Solar Flood Light

1.Determine the position of the vertical lamp; survey the geological conditions. If the surface is 1 m 2 soft soil,

the excavation depth should be deepened; at the same time, make sure that there are no other facilities

(such as cables, pipes, etc.) below the excavation position, and there is no long-term sunshade object on the

top of the street lamp, or change the position properly.

2.Reserve (excavate) 1 m 3 pits that meet the standard at the position where the lamps are erected; place the

embedded parts. The embedded parts are placed in the middle of the square pit, one end of the PVC conduit

is placed in the middle of the embedded parts, and the other end is placed in the storage place of the battery

(as shown in the above figure). Pay attention to keep the embedded parts, foundation and original ground on the

same horizontal plane (or the top of screw and original ground on the same horizontal plane, depending on the

needs of the site), one side should be parallel to the road; in this way, the lamp post can be upright without deflection

after being erected. Then, C20 concrete shall be poured and fixed. During the pouring process, the vibrating rod

shall not be stopped to vibrate to ensure the overall compactness and firmness.

 3.After the construction, clean up the residual sludge on the positioning plate in time, and clean the impurities on the

bolts with waste oil.

4.In the process of concrete solidification, the concrete shall be watered regularly for maintenance; the chandelier can be

installed only after the concrete is completely solidified (generally more than 72 hours)

 Installation of solar panel components
1. Before connecting the positive and negative poles of the solar panel to the controller, measures shall be taken to avoid short circuit;
2. The connection between the solar panel and the bracket shall be firm and reliable;
3. The output line of the component shall not be exposed, and shall be firmly tied with a cable tie;
4. The orientation of the battery assembly shall be toward the south, subject to the direction of the compass.

 Battery installation
1. When the battery is placed in the control box, it shall be handled with care to prevent damaging the control box;
2. The connecting wire between the batteries must be pressed on the battery terminal with bolts and copper gasket to enhance the conductivity;
3. After the output line is connected to the battery, it is forbidden to short circuit under any circumstances to avoid damage to the battery;
4. When the output line of the battery is connected with the controller in the pole, it must pass through the PVC conduit;
5. After the completion of the above, check the wiring at the controller end to prevent short circuit. Close the door of the control box after normal operation

Lamp installation
1. Fix the components of each part: fix the sun plate on the sun plate bracket, fix the lamp cap on the cantilever, then fix the

bracket and the cantilever to the main pole, and lead the connecting wire to the control box (battery box). 
2. Before lifting the lamp pole, check whether the fasteners at all parts are firm, whether the lamp head is installed correctly,

and whether the light source works normally. Then, whether the simple debugging system works normally or not; release the

connecting line of the solar panel on the controller, and the light source works.
3. Pay attention to safety precautions when lifting the main light pole; the screws shall be absolutely tightened. If the sunrise angle

of the component is deviated, it is necessary to adjust the sunrise direction of the upper end to the south.
4. Put the battery into the battery box, and connect the connecting wire to the controller according to the technical requirements;

connect the battery first, then the load, and then the solar panel; during the wiring operation, it must be noted that the wiring of

each circuit and the wiring terminal marked on the controller cannot be connected wrongly, the positive and negative polarity

cannot be collided, or connected reversely; otherwise, the controller will be damaged. 

7. Packing

For home garden lighting Motion 150W Sensor Led Solar Flood Light

8.  Producing & QC

For home garden lighting Motion 150W Sensor Led Solar Flood Light

 For home garden lighting Motion 150W Sensor Led Solar Flood Light   

9.About us

(1)Over 30 years history & Professional team  For home garden lighting Motion 150W Sensor Led Solar Flood Light   

(2)Factory area is over 7500 square meters

For home garden lighting Motion 150W Sensor Led Solar Flood Light

For home garden lighting Motion 150W Sensor Led Solar Flood Light

For home garden lighting Motion 150W Sensor Led Solar Flood Light

(3)All kinds of certification CE/SGS/ISO/ROSH  

For home garden lighting Motion 150W Sensor Led Solar Flood Light

10.FAQ

Q 1: Can I have a sample order?

A: Yes, we welcome sample order to test and check quality. Mixed samples are acceptable.

For home garden lighting Motion 150W Sensor Led Solar Flood Light

Q 2: What is the lead time?

A: Samples need 3-5 working days, mass products need 7-15 days.

For home garden lighting Motion 150W Sensor Led Solar Flood Light

Q3:How do you ensure the quality

A: We get three QC processes:1.For raw materials;2.During the half of production; 3.Final QC test one by one after aging 12 hours.

For home garden lighting Motion 150W Sensor Led Solar Flood Light

Q4:What is your MOQ?

Any quantity is welcome. We also provide a variety of customized services, such as color battery shells, color cartons and so on.

For home garden lighting Motion 150W Sensor Led Solar Flood Light

11.Contact us

ESG solar panel system, 30 Years History ,  Worthy of Trust  ! 

              We Welcome you to our Factory for a visit!  

Guangzhou ESG New Energy Technology Co.,LTD 

Phone/whatsapp/skype/wechat:+8613760893028

Address:202#,2nd Floor,Huacheng Industrial Zone,6-2,Yongheng Street,Shiqiao,Panyu,Guangzhou,Guangdong,511400,China

For home garden lighting Motion 150W Sensor Led Solar Flood Light

For home garden lighting Motion 150W Sensor Led Solar Flood Light