9.Solar Powered LED Street Lighting
Foundation pouring
1. Determine the position of the vertical lamp; survey the geological conditions. If the surface is 1 m 2 soft soil, the excavation depth should be deepened; at the same time, make sure that there are no other facilities (such as cables, pipes, etc.) below the excavation position, and there is no long-term sunshade object on the top of the street lamp, or change the position properly.
2. Reserve (excavate) 1 m 3 pits that meet the standard at the position where the lamps are erected; place the embedded parts. The embedded parts are placed in the middle of the square pit, one end of the PVC conduit is placed in the middle of the embedded parts, and the other end is placed in the storage place of the battery (as shown in the above figure). Pay attention to keep the embedded parts, foundation and original ground on the same horizontal plane (or the top of screw and original ground on the same horizontal plane, depending on the needs of the site), one side should be parallel to the road; in this way, the lamp post can be upright without deflection after being erected. Then, C20 concrete shall be poured and fixed. During the pouring process, the vibrating rod shall not be stopped to vibrate to ensure the overall compactness and firmness.
600w wind solar hybrid power generator street light
3. After the construction, clean up the residual sludge on the positioning plate in time, and clean the impurities on the bolts with waste oil.
4. In the process of concrete solidification, the concrete shall be watered regularly for maintenance; the chandelier can be installed only after the concrete is completely solidified (generally more than 72 hours)
600w wind solar hybrid power generator street light
Installation of solar panel components
1. Before connecting the positive and negative poles of the solar panel to the controller, measures shall be taken to avoid short circuit;
2. The connection between the solar panel and the bracket shall be firm and reliable;
3. The output line of the component shall not be exposed, and shall be firmly tied with a cable tie;
4. The orientation of the battery assembly shall be toward the south, subject to the direction of the compass
600w wind solar hybrid power generator street light
Battery installation
1. When the battery is placed in the control box, it shall be handled with care to prevent damaging the control box;
2. The connecting wire between the batteries must be pressed on the battery terminal with bolts and copper gasket to enhance the conductivity;
3. After the output line is connected to the battery, it is forbidden to short circuit under any circumstances to avoid damage to the battery;
4. When the output line of the battery is connected with the controller in the pole, it must pass through the PVC conduit;
5. After the completion of the above, check the wiring at the controller end to prevent short circuit. Close the door of the control box after normal operation
600w wind solar hybrid power generator street light
Lamp installation
1. Fix the components of each part: fix the sun plate on the sun plate bracket, fix the lamp cap on the cantilever, then fix the bracket and the cantilever to the main pole, and lead the connecting wire to the control box (battery box).
2. Before lifting the lamp pole, check whether the fasteners at all parts are firm, whether the lamp head is installed correctly, and whether the light source works normally. Then, whether the simple debugging system works normally or not; release the connecting line of the solar panel on the controller, and the light source works.
3. Pay attention to safety precautions when lifting the main light pole; the screws shall be absolutely tightened. If the sunrise angle of the component is deviated, it is necessary to adjust the sunrise direction of the upper end to the south.
600w wind solar hybrid power generator street light
4. Put the battery into the battery box, and connect the connecting wire to the controller according to the technical requirements; connect the battery first, then the load, and then the solar panel; during the wiring operation, it must be noted that the wiring of each circuit and the wiring terminal marked on the controller cannot be connected wrongly, the positive and negative polarity cannot be collided, or connected reversely; otherwise, the controller will be damaged.
5. Debug whether the system works normally; release the connecting line of the solar panel on the controller, and the light will be on; connect the connecting line of the solar panel, and the light will be off; at the same time, carefully observe the changes of the indicator lights on the controller; only when everything is normal, can the control box be sealed.
600w wind solar hybrid power generator street light
10.Installation Suggestion for Solar Powered LED Street Lighting
11.600w wind solar hybrid power generator street light process
12. 600w wind solar hybrid power generator street light Packing
